Showing posts with label maintenance. Show all posts
Showing posts with label maintenance. Show all posts

Monday, May 12, 2025

Little Maintenance Time

As always, maintenance is high on our list of priorities. You might wonder why. After all, I could just hire someone to handle it. Sure, that’s an option—but would they do it correctly? Besides, I have the time and the capability to take care of it myself.

One of the key tasks is inspecting power cords. Start by examining both the plug and the receptacle. Look for any discoloration or damage on the blades. Then, inspect the inside of the receptacle—are the sockets tight, clean, and free of debris?

If either the plug or receptacle has been replaced, take the time to open them up and inspect everything thoroughly. It's always better to be safe than sorry when it comes to electrical components.

Here’s an example: back in May of 2019, we were attending a rally in Fredericksburg, TX. On our way out, we stopped in Kerrville, TX, and stayed at the Elks Lodge for a few days. The lodge offered electric and water hookups, but no dump station.

Everything was working just fine—until we suddenly lost power. As usual, I jumped into troubleshooting mode to track down the issue and get it resolved.

If you look at the receptacle, you can see the reason for the failure in the third photo. It’s clear there was a problem. The first and second photos show the inside of the plug, which helped confirm what I suspected. Always good to document these things—what you find can be just as useful for learning as for fixing.

Burnt Plug

Burnt Plug


Reason for failure

After about an hour of work, everything was reassembled—and just like that, we had power again inside the coach. It’s always satisfying to track down an issue, make the repair, and see things working the way they should.





That’s exactly why ongoing maintenance matters. A repair might hold for a while, but it doesn’t mean it’ll last forever without rechecking. Catching problems early can prevent much bigger failures down the road.

Monday, May 8, 2025, was inspection day for that original fix. After all these years of service, it was finally time to take a closer look. And sure enough, the wear and tear was evident. Below, you can see the results—heat damage, fatigue, and signs of aging that can’t be ignored.

Time to replace and repair.










You will also notice I am using a new style of plug and Ferrell Crimps.

Press here to see the New Plug/Receptable I am now using. 


Safe Travel and Journeys 

DaGirls Rv, Gus Da Bus

Susan, Tilly, Dakota and me.



Thursday, May 9, 2019

Maintenance

Maintenance - Plug to Receptacle;

Recently Susan and I relocated to Round Rock, Tx., specifically to the Old Settlers RV park. A City Park with Full Hookups split with 30 and 50 amp sites. Be aware this is a no-frills park, with sites just big enough for a Alfa with slides out, without the awning. Upon setup, nothing abnormal was notice, plugged in and life was good. As we were leaving I notice this:


What I did not take was a photo of the plug looked like. When I remember to take additional photos, it was in the replacement process. The photo showing the damage to the plug, was a sight to see.


If you notice very closely, the Red wire (Leg 2) had come completely out of the terminal. The Green wire (safety ground) was burnt through the insulation.

As this was a Sunday, we knew we needed a replacement; we located a Camping World in New Braunfels. We arrived just as they opened and of course had to spend time looking around. Our destination was the Elks Lodge in Kerrville, Tx.

So, it was time for replacement of the damage plug and cord.


In replacing the plug this time, I had some wire sleeves, which I installed over the stranded wires. This allowed a firmer connection.

So, what is the take-away from this experience? Always look closely at both plug and receptacle.
What can cause a burnt plug – receptacle?
Loose connection, wire to terminal, inside the plug or the receptacle.
Loose connection, wire to terminal, circuit breaker.
Bad plug - receptacle.
Not being inserted all the way.

What can you do to prevent this?
Prior to plugging in, look closely at both the plug – receptacle.
Are the blades clean, is it a tight fit when plugged in. Is it inserted all the way?
Has your plug been replaced? If yes, have you opened the cover and ensure connections are tight.
Is the insulation of the cable pulled away from the strain relief? If it is a molded plug to cable, then replace it.
If it is a replacement plug, remove the strain relief, remove the cover, using black electrical tape (Not Cheap tape), wrap a few layers around the cable. 

Cost: Less than $30
Time: 1 hr.
Out of the way of our travels? No
 
Safe Travels and Journeys
DaGirls Rv
Susan, Tilly, Dakota and me

Guess Who -

July 29 —has it really been 76 days since our last post? Time flies when you're cleaning up puppy messes. Do you realize I entirely for...